Welcome to visit ceramic pump Middia website

How to avoid cracking when drilling holes in ceramic tiles? Here are some things you need to pay attention to! ! !

Release time:2024-11-04click:0

I believe you are familiar with the idea of ​​drilling holes in ceramic tiles. For example, the most common hook for placing towels in the bathroom needs to be drilled through the ceramic tiles. We also often see tile cracking during the drilling process, so how to avoid cracking when drilling tiles? Then you need to pay attention to these points, let’s take a look at it!

1. Punch location

① Before drilling holes, check whether there is a hollow in the tile. If there is a hollow, you need to reselect the position, because drilling holes in the hollow can easily cause the tiles to break and fall off. In addition, pay attention to the corresponding positions in the wall and avoid beams, columns, and water and electricity lines.

② The drilling position should be chosen at the joint of two tiles. If it is not suitable, it can be in the middle of the tile. It must not be chosen at the edge of a certain tile, as this will easily cause the tile to break.

③After determining the location, mark it with a pen or pencil.

2. Choose the right tool

Drilling may use impact drills, pistol drills, electric hammers and corresponding drill bits. Which one to choose and how to use it are all very particular.

It is generally believed that the drill bit for drilling tiles should not be a concrete drill bit, but a tile-specific drill bit or a glass drill bit (it is said that each can be purchased for 5 yuan in the building materials market).

The drill bit should be a hollow tube-shaped emery hole drill bit, followed by a bow-arrow-like ceramic tile hole drill bit. Currently, there are arrow-shaped drill bits on the market that are specially designed for drilling ceramic tiles, which are more convenient and faster.

3. Control the speed

In addition to tools, controlling the rotational speed is also critical. The speed should be low at the initial stage of drilling, and the speed can be increased appropriately after the glaze is drilled.

When using an impact drill, turn off the impact function and replace it with a ceramic tile drill bit. Generally, the impact drill has a flat drill bit. Turn to the flat drill bit first, and use low speed to gently remove a small amount of the glaze on the tiles. block, and then penetrate the tile layer at high speed, and then drive to the impact drill to continue drilling.

4. Control the size of brick holes

When using a glass drill bit to drill holes in ceramic tiles, first make a small pit in an oblique direction. If it is a big blowdiameter holes (such as smoke holes), use a drill to first make a circular mark on the tile, use a tile drill bit to drill a circle of holes around the mark, and then use the drill to make the operation easier.

5. Continuous watering

Water should be added for cooling during the drilling process, otherwise the drill bit will easily burn.

6. The punching force should be balanced

When drilling holes, do not use excessive force, and do not shake the drill from side to side.

7. Unblock the drill bit

After each hole is drilled, remove the drill bit and clear the blocked hollow part of the drill bit. This step is especially necessary for full ceramic tiles.

8. Heavy bolts should be long enough

Insert the expansion plug (plastic expansion tube) into the punched hole, and then you are done. Some masters said that if heavy bolts are installed on ceramic tiles, bolts that are 3 cm longer than the original bolts must be used, otherwise it will be dangerous.

9. Be careful when using electricity safely

Wear insulating gloves when using a drill.

The above content is the content of the article that the editor shared with you today about How to avoid cracking when drilling holes in ceramic tiles. After reading this, you will know what you need to pay attention to next time when drilling holes in ceramic tiles. Something! Eat melon.

lable:

Quick Links
Xiamen Middia Biological Ceramic Technology Co.,Ltd
Xiamen Middia Biological Ceramic Technology Co.,Ltd
address
address:Room 305, No. 891 Fanghubei 2nd Road, Huli District, Xiamen City, Fujian Province, China
Contact Us
  • Telephone:86-15396283716
  • E-mail:1617844001@qq.com

Copyright © 2010 ceramic pump factory,ceramic pump manufacturer,ceramic pump company,ceramic pump manufactor,ceramic pump price,ceramic pump telephone middia All Rights Reserved. XML map

Top